1. Disclaimer
2. Using this Manual
3. The Dirac Live® Product
3.1 Why Room Correction?
3.1.1 Dirac Live® Room Correction
3.1.2 End user benefits
3.1.3 What makes Dirac Live® unique?
3.2 Why Bass Control?
3.2.1 Bass Control vs. Bass Management
4. Initial Setup
4.1 System requirements
4.1.1 Windows
4.1.2 Mac
4.1.3 Dirac Processor Plugin compatibility
4.2 Network settings
4.2.1 Firewall
4.3 Microphone Setup
4.3.1 What is an omnidirectional microphone?
4.3.2 Why can't I use my cardioid or bi-directional microphone?
4.3.3 Where should I connect the microphone?
4.3.4 Microphone Access
4.4 Microphone & Speaker Placement
4.4.1 Speaker placement
4.4.2 Bass Control subwoofer setup
4.4.3 Microphone placement
5. Preparing the Software
5.1 Installing the software
5.1.1 Dirac Processor Plugin installation
5.1.2 Dirac Processor Standalone installation
5.2 Preparing Dirac Processor Plugin for Measurement
5.3 Preparing Dirac Processor Standalone (Windows) for Measurement
5.4 Preparing Dirac Processor Standalone (macOS) for Measurement
6. Dirac Live® 3 Calibration Guide
6.1 Dirac Live® account
6.2 Select Device
6.3 Common user interface items
6.3.1 Menu button
6.3.2 Accessibility settings
6.3.3 Auto-save
6.3.4 Help text
6.3.5 Notifications
6.3.6 Sidebar
6.3.7 Navigation bar & buttons
6.4 Select Recording Device
6.5 Volume Calibration
6.6 Select Arrangement
6.6.1 Tightly focused imaging
6.6.2 Focused imaging
6.6.3 Wide imaging
6.7 Measurement Procedure
6.8 Filter Design
6.8.1 Speaker groups
6.8.2 Target curve
6.8.3 Curtains
6.8.4 View options
6.8.5 Impulse response view
6.9 Bass Control Filter Design
6.9.1 Bass Control Options
6.9.2 Crossover Design
6.9.3 The Bass Control Target Curve
6.9.4 Applying Bass Control Adjustments
6.10 Filter export
7. Final remarks


Dirac Research AB cannot be held responsible for the improper use of configuration of the Dirac Live® software, or for any damage that might occur because of this improper use or configuration. This manual is intended to provide a guide for proper use of the software, but possibilities for use are such that no manual can be considered exhaustive for every scenario. Therefore, in addition to reading and understanding the material contained in this guide, we encourage you to utilize caution when using the Dirac Live® software, as misconfiguration, especially regarding output gains or boost, can produce signals that may damage your audio system or hearing.

Using this Manual

This manual provides instructions for setting up and using the Dirac Live® desktop software, including the bundled Room Correction feature, additional Bass Control feature, the Dirac Processor Plugin package, and the Dirac Processor Standalone desktop software. Dirac Live® Room Correction and Bass Control can be applied to compatible home AVRs and Hi-Fi receivers. The Dirac Processor Plugins in VST, AAX, and AU format currently support Dirac Live® Room Correction and are designed for use with desktop plugin hosts and professional DAWs. Dirac Processor Standalone software provides systemwide Room Correction for desktop devices. For additional guidance and walkthroughs, please consult the Dirac Knowledge Base.

The Dirac Live® Product

Dirac Live® is a room acoustic solution that enables users to measure and optimize their sound systems to their preferences and reduces sound colorations introduced by the room. Dirac Live® has two features: Room Correction, included with every software package, and Bass Control, an add-on feature available as separate purchase.

Why Room Correction?

Your listening space impacts sound. Walls, floors, windows, and furniture all affect how sound waves travel, maximizing certain frequencies while weakening others. Furthermore, speakers might not be placed optimally. For instance, they may not be placed symmetrically, meaning the left and the right channels arrive at the listener at different times. This leads to distorted stereo imaging. Speakers can interfere with each other as well, cancelling out at certain frequencies.
Without addressing these acoustic challenges, your audio system at home sounds worse than intended, regardless of price. Muddy sound, distorted soundstage and flabby bass are extremely common sound quality issues, even in the most expensive setup. Click here to dive deeper into the four types of distortions good digital Room Correction system should address.

Dirac Live® Room Correction

Dirac Live® provides world-class Room Correction with its patented mixed-phase technology and time domain correction that other solutions are missing. Dirac Live® is proven to deliver unparalleled Room Correction performance, minimizing the room's impact on sound. Loaded with sophisticated algorithms, Dirac Live® is at the same time extremely easy to use, with an intuitive user interface and step-by-step guidance that allows for easy setup and precise personalization of the target sound curves.

End user benefits

What makes Dirac Live® unique?

Why Bass Control?

Your listening space interferes with sound, and speakers interfere with one other. To be specific, walls, furniture, and the floor all reflect sound waves, which alters their timing and frequency. This can create standing waves, leading to inconsistent bass. Different speakers can also play the same sound at different times, creating interference. In traditional bass management setups, the bass-managed speakers and subwoofers interfere with one another in an uncontrolled way. The severity of these effects can vary from mild to severe, depending on the location and speaker placement.
What does this mean for your listening experience? Bass becomes spatially inconsistent across the listening space. In some spots, you hear almost no bass. In others, you get booming bass. And when multiple subwoofers are added to the sound system, it becomes a tremendous challenge to utilize them properly in creating spatially consistent bass. Without Bass Control, it takes tremendous experience, time, and cost to address such issues, and if you hire a professional calibrator, you will have to call them back every time you change or move your equipment.

Bass Control vs. Bass Management

Bass Control is fundamentally different from traditional bass management solutions. Bass management is a common AVR function that extracts bass content from input signals and routes it to connected subwoofers. Bass Control does offer bass management functions, but the core value of Bass Control is that it co-optimizes speakers to improve bass accuracy and ensures consistent bass performance throughout the listening area from a single- or multiple-subwoofer setup. Put simply, each subwoofer is tuned as part of a complete unit in your listening space, leading to a consistent and realistic response, no matter the arrangement.

Initial Setup

System requirements

Dirac Live® 3 requires a Windows or macOS computer with the following minimum specification:



Dirac Processor Plugin compatibility

If not using the Dirac Processor Plugin, skip this section.
The Dirac Processor Plugin package requires a plugin host compatible with VST2, VST3, AAX, or AU plugins. Compatible hosts include but are not limited to:

Network settings

The Dirac Live® 3 desktop application and any Dirac Live®-supported hardware need to be connected to the same network to facilitate communication. The Dirac Live® 3 desktop application also requires access to the internet. This is for two reasons: to access the license server and because part of the filter design is calculated on a cloud server. Therefore, it is important to make sure that the firewall does not block the connection from the application.


Configure your firewall to allow connections from Dirac Live® 3.

If you are using Kaspersky, please see the following guide:

Microphone Setup

Dirac Live® 3 requires an omnidirectional calibration microphone with an associated calibration file. We suggest the miniDSP UMIK-1 microphone due to its ease of use and universal drivers. Please note that the measurement microphone is not included in the Dirac Live® software purchase. 

What is an omnidirectional microphone?

An omnidirectional microphone is equally sensitive to sound from every angle. An omnidirectional microphone's polar pattern is a circle, indicating that gain is equal for any inclining angle relative to the microphone. In contrast to a bi-directional microphone, the omnidirectional microphone has only one side open to sound pressure.

Why can't I use my cardioid or bi-directional microphone? 

Dirac Live® 3 requires that sound pressure from the room's reflections and the speakers' lines-of-sight are measured with equal gain. A cardioid or bi-directional microphone will measure the sound with different gain depending on sound waves' inclining angles to the microphone. Measuring a surround system with a cardioid microphone pointing at the front speaker will measure lower gains for the speakers behind the microphone, preventing the system calibration from being robust. 

Where should I connect the microphone?

If the Dirac Live®-enabled device comes with a calibration microphone, we recommend connecting the included calibration microphone to the device and not the computer, as Dirac Live® 3 fetches the calibration file from the device automatically.
If using a third-party omnidirectional microphone, or if your Hi-Fi device is placed far away from your listening area, connect the microphone to your computer and ensure it is accessible as described in §4.3.4. Download the relevant calibration file provided by your microphone manufacturer and load it into Dirac Live® 3 as described in §5.6. Applying proper calibration to your microphone is crucial to creating a reliable measurement.

Microphone Access

If the calibration microphone is connected to the computer, Dirac Live® 3 (and the plugin host application if you are using the Dirac Processor Plugin) needs access to the microphone to complete measurement.


Go to "Sound Settings."
Under "Related Settings," select "Sound Control Panel."
Select the microphone you want to use for the calibration.
Click "Properties" and then choose the Advanced tab.
Make sure that both checkboxes under "Exclusive Mode" are selected.
If visible, uncheck the box under "Enable audio enhancements."

Ensure the checkbox for "Enable audio enhancements" is unchecked.


  1. Go "System Preferences" → "Security and Privacy."

Under the "Privacy" tab, select "Microphone" and check the box next to Dirac Live® 3.

Microphone & Speaker Placement

Dirac Live® 3 uses measurements made in your listening room to calculate correction filters for all speakers and subwoofers. The Dirac Live® 3 app will guide you through the measurement and filter design procedure, where you will take measurements at different locations in your listening room and create a correction filter. 

Speaker placement

Before you begin calibration of your system, it is important to ensure that your speakers themselves are in a suitable arrangement and position. Below are a few guidelines to follow when determining the physical arrangement of your setup.

  1. Check your speaker manufacturer's recommendations for setup and follow these first. They might suggest steps that conflict with our guidance below and are to be followed first and foremost.

Maximize distance between your speakers and the wall, if possible. This will reduce the interference of high energy wall reflections, which often affect lower frequencies. Dirac Live® will be able to correct for this distortion in many cases, but sometimes too much energy is lost and the speakers need to be moved further away from the wall.
Do not place objects in front of the speakers.
If possible, position the normal listening spot in the middle of the room.
Consider adding dampening in the room. This reduces the impact of room modes or flutter echo.
Place your speakers at the same height as your ears.

Bass Control subwoofer setup

Microphone placement

The basic principle of microphone placement is that any additional measurement improves the correction. More points = more accurate filters. However, depending on your room's acoustics and equipment, the benefit from more measurements may diminish faster. We recommend completing every measurement point in your chosen arrangement.

Preparing the Software

Installing the software

Download the latest version of Dirac Live® 3 from and save it to a suitable location.
Open the downloaded file and follow the steps in the installer.
After installation, make sure your device is connected to the same local network as your computer. Your computer also needs to be connected to the internet for licensing purposes.
If you are using Dirac Live® 3 alongside a home AVR, skip to §6.0. If you are using Dirac Live® 3 alongside the Dirac Processor Plugin or Dirac Processor Standalone, read §5 below.

Dirac Processor Plugin installation

If not using the Dirac Processor Plugin, skip this section.
Unless you specify a different location during installation, the Dirac Processor Plugins will be placed in the following folders:



Dirac Processor Standalone installation

If not using Dirac Processor Standalone, skip this section.
You can download Dirac Live and Dirac Processor Standalone application here. Make sure that your computer is connected to the internet for licensing purposes.
Open the files and follow the installation procedures.
Restart your device before continuing.

Preparing Dirac Processor Plugin for Measurement

If not using the Dirac Processor Plugin, skip this section.
Start your plugin host or DAW and locate the DiracLiveProcessor in the plugins menu. Depending on the host application, it might be under the subheading "Dirac Research."
Because plugin host settings vary, you might need to go through additional steps to activate the DiracLiveProcessor. In this case, consult the documentation for your chosen host application for full instructions.

Once you have added the DiracLiveProcessor to your host of choice, open it.
Log in to your Dirac account in the sign-in window.

The Dirac Processor Plugin will not contain any filters at this stage unless you have previously created one with Dirac Live® 3.

Start a gapless audio stream inside your DAW or plugin host by looping an instrument or playing a long track, such as this gapless 30-minute test mp3. Press the "play" button in your DAW to ensure that the audio stream is active while Dirac Live® Measurement is being executed. It is extremely important that the audio stream is active during the whole calibration process.

Preparing Dirac Processor Standalone (Windows) for Measurement

If not using Dirac Processor Standalone, skip to §6.0.
Open the Windows Control Panel and select Sound. This opens Windows Sound Settings.
The Standalone is not active until the application Dirac Processor Standalone is started, which comes later.

Select your default sound device and click Configure.

Select the configuration that you want to use. Note: For some sound cards that use ASIO, it is not possible or necessary to select a Multichannel configuration here. If you are using WASAPI driver, it is necessary to select the proper configuration.
Open the Dirac Processor Standalone.

Log in to your Dirac account if necessary.

The Processor window will look empty the first time you open it. You will populate this window with filters after you have created them in Dirac Live® 3.

After Starting Dirac Processor Standalone, the new sound device will be active and selected as the default sound device.

In Dirac Processor Standalone, select Options > Audio Settings.

Select the number of channels relevant for your system.
Select Audio Device type from the following (Windows Audio modes are WASAPI modes):
Windows Audio operates in shared mode. The audio pipeline does not take full control of the driver. Instead, it shares system audio resources with other applications.
Windows Audio (Exclusive Mode) dedicates all system audio resources to Dirac Processor Standalone and takes over Windows' audio pipeline.
Windows Audio (Low Latency Mode) is an alternate Windows Audio configuration. Low Latency Mode uses the latest available Windows audio interface in a shared mode, but supports low latency.
ASIO (Audio Stream Input/Output) is a third-party sound card driver protocol specified by Steinberg, providing a low-latency and high-fidelity interface between Dirac Processor Standalone and the computer's sound card.Source
When using Windows Audio settings, you will use the Windows Sound Settings panel (described above) to change channel configuration and sample rate, etc.When using ASIO settings, you will use Processor + the ASIO driver program to change channel configuration and sample rate, etc.
Select your "normal" sound device as output. If you have ASIO drivers for your sound card, select ASIO as the Audio Device Type.
Click "Test" to ensure sound playback is functional. If so, close the Audio Settings window.
Play a sound from your media player or web browser to make sure the level meters are moving and that the sound is audible.

If you experience dropouts in the sound, experiment with different buffer-sizes. 10.0ms latency is recommended. However, it is not available for some sample rates.
In some media players like JRiver, you need to select the output manually. In this case, make sure "Standalone (Dirac)" is selected.

You are now ready to perform a measurement and create your first filters.
Download and Install Dirac Live® 3 and Dirac Processor Standalone
You can download Dirac Live® 3 and Dirac Processor Standalone here. Make sure that your computer is connected to the internet for licensing purposes.

Preparing Dirac Processor Standalone (macOS) for Measurement

If not using Dirac Processor Standalone (macOS), skip to §6.0.
Start DiracLiveProcessor in Applications

Log in to your Dirac account if necessary.

The Processor window will look empty the first time you open it. You will populate this window with filters after you have created them in Dirac Live® 3.

In Dirac Live Processor, go to Options → Audio Settings.. and select the audio interface you want to use.

Open Audio MIDI Setup and make sure Dirac Virtual Audio Device is in the list of soundcards

Play a sound and make sure the sound is passing through the Dirac Live Processor

You are now ready to perform a measurement and create your first filters.

Dirac Live® 3 Calibration Guide

Dirac Live® account

Lauch the Dirac Live® 3 desktop application you installed previously.
On the first screen that appears after launching the application, you will enter your account details. Depending on the manufacturer, your Dirac Live®-enabled device may or may not include feature license(s) by default. If you bought a feature from our webstore, you must log into your account in the application to access it.
If you do not have an account, you may create one by clicking "Create or manage your account" on the login screen.
If you have not bought any licenses and do not wish to log in, you can press the "Proceed without logging in" button.

Select Device

Next, Dirac Live® 3 will scan your network for all compatible devices. Make certain your device and the computer are connected to the same network and have full network access. All found devices will be listed. If your device is visible but crossed out, you lack the proper license for using it. Purchase the proper license from our webstore and try again.

If you have trouble with device discovery, see: Troubleshooting: No Devices Found
You can also try using the "connect via IP" by pressing  at the top of the application and entering the device's IP, which can usually be found inside its firmware or included documentation. If the device still does not appear, ensure that there is no firewall blocking the connectivity between the device and Dirac Live® 3. Kaspersky on Windows can be particularly problematic. Here is our guide to fixing it: Windows: Problems with Kaspersky

Common user interface items

Once you have selected a device, you will enter the Select recording device page, which starts the calibration procedure. This section describes the function of the common user interface items available during the whole calibration process. 

Menu button

The menu is found by pressing the Menu button in the left upper corner. The menu includes some standard user features such as saving and loading projects, application themes, languages, etc.
Supported languages include English, Japanese, Mandarin, and Swedish.

Accessibility settings

In Accessibility, you can adjust the application design to fit various forms of color blindness.


After each measurement is taken, the project is auto-saved. The auto-saved project can be found in:





Help text

If you get stuck and do not know what to do during the application, you can always press the help button  . Pressing the help button will give you the necessary information on how to proceed with your calibration. For example, the help text for the Select recording device page can be seen below:


Dirac Live® 3 uses several types of notifications to keep the user updated about changes or errors. Yellow indicates an error. Green indicates that the procedure was successful. Black and blue are general notifications.


The sidebar presents general information about the connected device, such as manufacturer, logo, model, and system name. The filter available on the unit can be seen under "Filters." The sidebar can be minimized by pressing the section between the sidebar and the rest of the page described with a blue line in the figure below.

Note: Depending on your device, changing the configuration may clear the filter list or switch to a configuration-specific filter list. You should never change device configuration while performing a Room Correction.

Navigation bar & buttons

At the bottom of the page, you will find two buttons for navigating forward or backward in the application.
The navigation bar at the top of the page shows where you are in the application. You may also navigate directly to a page you have visited previously by pressing one of the black circles.

Select Recording Device

After you have selected a device, you will need to select a microphone to record the stimulus, or test tones, played by your device. All microphones connected to your computer and your device will be listed on the "Select Recording Device" page.

Select the microphone that you wish to use for measurements—usually the one you connected during setup. Click the bottom of the microphone's box to load the relevant calibration file. Selecting "No calibration" after clicking the context menu bypasses any compensation to the raw input stream and is not recommended.   Make sure that the microphone calibration file is created for 90-degree measurements. 

After choosing the calibration microphone and loading a calibration file, you want to proceed to the "Volume Calibration" page by pressing the navigation button in the lower right corner. 

Volume Calibration

Since the filter design algorithm requires that the speakers be measured with a moderate sound pressure level and a noise level as low as possible, it is crucial to do a level calibration of the system before measurement. The microphone should first be positioned in the center of the listening area. This is the "sweet spot." 

  1. The "Master output" level must be set to a low volume to avoid damage to your ears or speakers. If it is not already set to a low volume, drag the indicator to the lower part of the slider.
  2. Set the Mic gain to the bottom of the red section, which represents +0dB digital gain.
  3. Press the play button beneath the speaker located furthest to the left. The speaker should now play a stimulus in the form of a pink noise or, if the speaker is a subwoofer, short sine sweeps. If you cannot hear the stimulus, slowly raise the "Master output" level until you hear it.
  4. Repeat this procedure for all speakers. If there is no noise playing from one or more speakers, make sure that your device is configured to the correct speaker configuration and that your speakers are connected to the device. Ensure that the device's firmware is also properly recognizing each speaker.
  5. Adjust the Master Output to a normal or slightly louder-than-normal listening level for Measurement and then proceed.

If you receive a Signal-to-Noise Ratio error during Measurement, you will need to increase Master Output or decrease Mic Gain at the Volume Calibration stage.
If you receive a Clipping error during Measurement, you will need to decrease Master Output at the Volume Calibration stage.

Remember that volume of the stimulus should never hurt your ears. There is a lock on the Master output slider for safety reasons. However, if you need to raise the volume into the red zone and are positive that your system can handle it, press the red lock that appears above the slider. You should now be able to drag the slider into the red area.

Select Arrangement

In the "Select Arrangement" view, select the arrangement that best matches the arrangement to be measured. The variations we offer act as a guide to positioning the microphone. The core difference between the arrangements is the number of measurement points that are allowed.
The first measurement should always be taken in the center of the listening region, in the desired sweet spot, as this will be used for aligning levels and delay between speakers.

An arrangement can be chosen from the arrangement menu. In the arrangement menu, the home section has three different arrangements: Tightly focused imaging, Focused imaging, and Wide imaging, which provide 9, 13, and 17 measurement points, respectively.

Tightly focused imaging

This measurement arrangement represents a well-defined listening area from which the listener rarely moves. Note: The tighter the measurements are placed, the more extreme the correction.

Focused imaging

The measurement arrangement represents a listening area with one well-defined listening position that should still accommodate a degree of flexibility. Select this arrangement if the listening area is a two or three-seat sofa.

Wide imaging

This measurement arrangement represents a larger listening area for multiple listeners. This setting works for both corner sofas and for listening areas that are distributed across two or more sofas.

Tip: It is recommended to spread out measurement points evenly across the whole listening area. However, for the "Wide" and "Focused" listening arrangements, measurements can be taken more densely at a specific position to emphasize it more strongly. 

Measurement Procedure

Ensure there is a clear line-of-sight between the microphone and speakers, no background noise (TV, air conditioning, construction work, etc.) while doing the measurements, and remember to keep the microphone perfectly still, using a stand or similar. A sweep will be played through each speaker, and a final sweep will be played through the first speaker again.

  1. The first measurement should always be taken in the center of the listening region, in the most used listening position or "sweet spot," as this will align levels and delays between speakers. 

Press the measure button to collect a set of measurements. This will play a sweep in each speaker and one final sweep in the first speaker again.
Press the timer to select a delay between 2-15 seconds before the measurement start. This will give you time to get out of the listening area, or to lower your laptop lid if it interferes with line-of-sight.
Move the microphone to the next indicated position and press "Measure." Repeat this procedure for all measurement points or until you have spanned the whole seating area. Tip: Hover over a measurement point to get a help text on where the point should be positioned.

Proceed to the filter design page after all recommended positions have been measured.

Your project will now be auto-saved 
Potential problems and workarounds during measurement: 

Filter Design

For guidance on Bass Control Filter Design, see §6.9.
With the measurement done, we have all the information to correct for any distortion in the system. The filter design page shows each speaker's averages frequency response before & after Dirac Live® has been applied. The frequency response itself shows how much energy the speaker can produce for a certain frequency. For example, in the figure below, the room resonance has caused a 10 dB energy boost at 60 Hz and 5-10 dB attenuation above 100 Hz. A sharp peak like this at 60 Hz will amplify some bass notes more than others making the bass reproduction of the system uneven. The valley above 100 Hz will reduce the feeling of warmth of the system. These are distortions that Dirac Live® 3 will correct.

Tip: You can zoom in and out by using the wheel on the mouse. 

Speaker groups

Speakers with similar physical attributes are automatically grouped. Speakers within a group will have the same target curve and, in turn, also have a similar frequency response. If you want individual target curves for the speakers within a group, you can separate the speakers by dragging a speaker from within a group to the empty area shown in the figure below.

Target curve

The target curve is a tool to edit the frequency response of a speaker or a group of speakers. Dirac Live® 3 will construct a mixed-phase filter to make the systems frequency response mirror the target curve. Dirac Live® 3 will automatically generate suggested target curve(s) and resulting filters intended to make the sound image in your room as even as possible. These curves can be adjusted to your preferences.

The target curve can be modified (and emphasis on a particular frequency increased or decreased) by dragging the control point.

Control points can be added by right-clicking on the target curve and selecting "Add control point." A control point can also be deleted by right-clicking on it and pressing "Delete control point."

At any time, you can load the default or custom target curve from the menu in the upper left corner. Choose between loading the target curve to a specific group or all groups.

Tip: A minor change to the target curve can dramatically change the perceived sound quality. It is therefore recommended to edit the target curve with care and awareness. You can play around with some different target curves by exporting different filters to your device and finding the one you prefer. Save your project often to give yourself the latitude to make adjustments without committing to any potential negative side-effects. If you experience phase issues from an exported filter, you may have measured too few measurement points or measured in too small an area. You can always go back to the Measure page and re-measure points or measure more. The default target curve often attenuates the bass response of the room. Many users prefer to amplify the bass region to mirror the room's natural response. This can be done by adding a 6 dB bump under 100 Hz, as shown below.


Curtains can be used to restrict the area that is going to be corrected. The light grey area on the curtain's right is going to be corrected in contrast to the dark grey area left of the curtain, which will not be corrected. Hovering over the curtain will highlight it in light blue. The curtain can be dragged by pressing the left mouse button over the curtain. The dashed line is the detected lower cutoff frequency for the speaker. It is not recommended to drag the curtain below this point since the speaker is not designed to produce energy at these low frequencies.

View options

Dirac Live® 3 offers several view options, making it easier to study the characteristics of your system. System measurements without Dirac Live® applied can be seen to the left, while the corrected system with Dirac Live® applied can be seen to the right.


The average frequency response of all measurements for a speaker can be seen if this box is checked.


Shows the spread of the frequency response for a speaker. For a specific frequency, the highest and the lowest measured energy is shown.


Take snapshot function will create a snapshot of the current state – if a change is made to a target curve, it is possible to switch between snapshots without saving/load projects.

Impulse response view

The impulse response illustrates the precision and distinctness of the sound before and after Dirac Live® compensation. Each speaker's impulse response can be seen by pressing the "Impulse response" tab in the upper left corner.

Pressing "separate curves" in the view options under Impulse response will split the impulse view horizontally. The corrected impulse is then seen below, with the measured impulse on the top. The measured impulse's detected peak is positioned at 0ms and the corrected impulse peak is positioned a few milliseconds later—typically around 7ms. This is the true latency of the filter introduced to the system and is needed to correct for the mixed-phase behavior of any speaker. In the figure below, we can study the drivers' misalignment in the speaker, where the energy is spread out over time. After Dirac Live® correction, the impulse response's energy is well defined over a small period, making the sound sharper and more detailed.

Bass Control Filter Design

The purchase of Bass Control gives you access to new features and optimizations designed to bring out the best in your system's low end through fundamental improvements to timing, response, and roll off.

Bass Control Options

There are three options for Bass Control inside a compatible project: "Off," "Upmix Only" and "Full Bass Optimization."

After selecting "Full Bass Optimization" or "Upmix Only," several magnitude response plots will be shown in the graph. These plots present the average magnitude response of the selected speaker (highlighted on the right panel) and all subwoofers. These plots, generated by calculations in the Dirac Live® software, help in choosing the best crossover frequency for the system.

Crossover Design

  1. Based on this insight, select a crossover frequency where both the selected speaker and the subwoofer(s) have energy. The crossover frequency can be adjusted by dragging the crossover bar.
    1. Crossover filters are highlighted when hovering over the crossover bar. Illustrated above, the lower section (A) of the crossover filter describes which frequencies are passed to the subwoofers. The middle section (B) describes which frequencies are passed to both the subwoofers and the high-range speaker, and the upper part (C) describes which frequencies are passed to the high-range speaker.
    2. Note that each speaker group has its own crossover frequency.

The Bass Control Target Curve

In Dirac Live® 3, the system's frequency response is adjusted through a target curve. With Bass Control, lower frequencies are highly correlated between speakers. Therefore, the target curve is separated into a low-frequency section that is universal across the system and a higher-frequencies section that is unique to each speaker group. This segmented target curve is described below:
For the selected speaker group, the target curve consists of the bass-controlled range, which is common to all channel groups, as well as the range of higher frequencies, which is unique to that group. Each group specifies their own crossover point.
The target curve defaults to a flat correction, which represents a transparent sound that does not add any additional coloration. If you want to change the character of the correction, drag the target points on the target. You can add more points by right-clicking on the target curve and select "Add control point to."
Dragging the curve above the 0 dB level on the Y-axis boosts the adjusted frequencies. Dragging the curve downward under the 0 dB level attenuates them.
Increasing the volume of the subwoofers can be achieved by raising any point below 100 Hz on the target curve by a few dB, as illustrated below. Such a boost can be desirable when watching movies that utilize low-frequency effects.

Applying Bass Control Adjustments

Once you have designed your ideal crossover frequency and target curves for each group, press "Calculate" in the lower right corner. The bass control filters will now be calculated.
After the Bass Control calculation is done, select the "Corrected" checkbox in the plot options to show the resulting input magnitude response for the selected channel. The corrected curve should conform to the target curve, as illustrated below.
Click "Proceed to Filter Export."

Filter export

The last step of the process is exporting the filter generated by Dirac Live® 3 for a live listening test. Select a slot and save under the desired name (there may be an auto-generated name, which can be replaced). When the export is complete, the application will return to the Filter Design view. Do not forget to save your project before closing the application.

Final remarks

Thank you for reading this manual. We hope that it provides all the answers you need for getting a Dirac Live®-calibrated system up and running. However, if you experience trouble with anything not mentioned in this guide, please feel free to contact our support team at Dirac Live® User Manual –